How To Install A Toilet Paper Roll

Sam Kear enjoys working on weekend DIY home improvement projects.

If you lot're moving into a new home or remolding a bathroom, you may need to install a toilet newspaper holder. Even if you don't plan to move anytime shortly, over fourth dimension, bath tissue holders wear out and eventually need to be replaced as well.

In this article, I'm going to walk yous through the process of installing a toilet paper holder in your bathroom step by step.

9 Simple Steps to Install a Toilet Newspaper Holder

1. Determine Location
2. Gather Tools
3. Prep the Supplies
4. Place Template on Wall
5. Level the Template
6. Find Studs in Wall
7. Drill Airplane pilot Holes
8. Install Mounting Brackets
9. Finish Upwardly

ane. Where to Hang the Toilet Paper Holder

Choosing the location for mounting the holder can be the about hard office of this job. Each bathroom is unique, so you may need to make slight adjustments for your particular state of affairs. Yous might want to experiment with several locations before you start to drill the mounting holes.

Standard Location

The rules aren't set in stone, but the mostly accustomed standard is to mount the holder on the wall 26 inches above the floor and 8 to 12 inches in front of the toilet.

Other Possibilities

If there isn't a suitable location to the left or right of the toilet, you can consider a couple of other options.

1. In front of the toilet: You can mount the holder on a wall in forepart of the toilet 26 inches high. This option, however, is but feasible if the holder would still be within reaching altitude.
2. Freestanding holder: If you can't decide on a mounting location, y'all can buy a non-mounting holder instead. Freestanding holders can be easily moved to another location without having to drill holes.

In club to mount the bath tissue holder, you will demand the tools listed below. A stud finder is optional, but it does make the chore a lot easier.

• Power drill with drill bits
• Bubble level
• Screwdriver
• Masking tape
• Stud finder (optional)
• Hammer (if using drywall anchors)

Make sure yous take all the parts you lot need before you lot start.

3. Prepping the Parts

Earlier I commencement on any project, I similar to brand sure I have all the parts I'll need to consummate it. Open up the box for the holder y'all'll be installing and make sure yous have everything y'all need.

You tin can besides dry-fit the pieces to see how they will go together earlier yous start to drill.

Nearly kits include a paper mounting template to assist with drilling the holes. Locate the template in your kit and cut it out if necessary.

Whorl to Proceed

Read More From Dengarden

four. Placing the Template on the Wall

The side by side step after selecting a location is to tape the template to the wall. Yous should employ masking or painter's tape to attach the template and so the paint won't be damaged.

The template will marking the location where the holes will exist drilled for the bracket. If you lot want to get an thought of what the holder volition look like, you tin can hold information technology up against the template.

Record the mounting template to the wall using masking tape.

5. Make Certain the Template Is Level

Place your level along the top border of the template and make sure it is completely level. If the template isn't level, the holder will non be level once information technology'south mounted.

If you need to make any adjustments, loosen the record and re-level the template. This step is very of import, so you might want to double-check your work.

Make sure the template is level before y'all commencement to drill.

six. Locate Any Studs in the Wall

Next, use a stud finder to determine if yous will be drilling into whatever studs. Slowly movement the stud finder along the wall and mark whatsoever studs you lot run across.

If y'all discover that any of the holes will be drilled into a stud, it's not necessarily a problem, but yous volition not need drywall anchors for those holes. Some people really prefer to take at least one ready of mounting holes become into a stud for added stability.

If you lot don't accept a stud finder, you can gently tap on the wall to wait for the studs.

Apply a stud finder to mark the location of whatever studs on the wall.

vii. Drill the Pilot Holes

Afterward making sure the template is located in the proper location you can begin drilling the pilot holes.

1. Utilise the drill bit size listed in the instructions.
2. Making certain the drill is level carefully drill holes in the locations marked on the template
3. Remove the template afterwards all holes have been drilled, most mounting systems require iv holes.

Drill the holes using the bit size specified in the instructions.

8. Installing the Mounting Brackets

1. Using a hammer, tap the drywall anchors into the spiral holes. If the holes go into a stud, you will not need the anchors.
2. Secure the mounting brackets to the wall using the screws in the kit.
3. Place the holder on the mounting brackets
4. Secure the holder to the brackets by tightening the lock screws. The lock screws should exist on the bottom so they cannot exist seen.
5. Brand certain the holder sits flush against the wall.

Secure the brackets to the wall using the screws.

9. Finishing Up

Drilling holes in drywall tends to create a lot of dust, so I recommend cleaning information technology up with a vacuum as soon as possible.

Gently pull on the holder to make sure that information technology is attached securely to the wall. If the holder moves when you impact it, become back and brand certain all of the screws are fully tightened.

Now that you've successfully completed this projection, y'all can easily install other items such as towel bars and towel rings, which typically utilise very similar mounting systems.

This article is accurate and true to the best of the author'south knowledge. Content is for advisory or entertainment purposes only and does not substitute for personal counsel or professional communication in business concern, fiscal, legal, or technical matters.

David on December 27, 2022:

Tin't become the toilet paper bar set up screws to attach to the brackets

Ted on September 01, 2022:

Ppo, your screws are most likely in those holes. Often times they are painted over past blow. Try scraping out the hole, you may discover a tiny flathead screw

ppo on August 22, 2022:

My toilet paper holder and towel confined have small slot under the round bases however, I cannot run across a screw of whatsoever kind all I tin see is a minor metal flat piece most the opening...how do I take these off the wall!! Thanks

Keri Machin from Miami Florida on August 25, 2022:

overnice guide. such a basic thing but i had to look it up lol

JOAT2 on January 26, 2022:

If you are installing a toilet newspaper holder that has only one attachment (single mount) to the drywall, you will need to either install the screw into a stud or utilise a toggle bolt (other anchors might work, but non as securely). The larger the toggle commodities, the more secure it will be, but only use one that is large enough to hold securely. Other types of anchors tend to twist when torque is practical to the toilet paper holder through normal use.

Source: https://dengarden.com/home-improvement/How-to-Install-a-Toilet-Paper-Holder-in-a-Bathroom

Posted by: colonhiciand.blogspot.com

Share this post